- Battery Holder with Connector DC Jack
- Battery Holder with (ON/OFF) Switch Cover
- Suitable model: AA / AAA / 3.7V 18650 / 9V
- Light and durable Hard Plastic.
- Battery sold separate
- Cable: 15cm
- Rated current: 10A
- Rated voltage: 250V
- Maximum power: 2500W
- Line Specifications: 3*0.75mm square
- Product material: flame retardant PC material + plastic
- Product size: 48cm*5.5cm*3cm
- Product weight: 0.47Kg
- Product length: 1.8 M
- Product use: Cabinet special power
Input Voltage: DC5V
Base Type: Wedge
Size: 15cm x 1.5cm
Cable Length: 1.2m
Input Current: 1.4A
Color Temperature: Cool White:6000-6500K
Connecting Method: USB
Material: Aluminum & PVC
Application: Widely used as wardrobe light , reading light , wall light ,Cabinet Light, Showcase Light , night lamp and so forth.
Material: Metal Revolving
Total Length: 36mm Motor
Shaft Size: 3mm(diameter)*10mm(length)
Type: Step-Up Voltage Regulator
Inrush Current Rating: 2 A
MPN: Does Not Apply
Nominal Current Rating: 2 A
Output Voltage Rating (AC): 24 V
Nominal Voltage Rating (DC): 24 V
* Module Properties: non-isolated step-up module (BOOST)
* input voltage: 1-5V
* Output voltage: 5.1-5 .2 V
* Output Current: Rated 1A-1.5A (single lithium input), the maximum 1.5A (single lithium input)
* Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
* Switching frequency: 500KHz
* Output ripple: 30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
* Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off)
* Operating Temperature: Industrial (-40°c to +85°c)
* Full load temperature rise: 30°c
- Imported active formula to enhance solder flow and improve soldering ability.
- Green, environmentally friendly emissions, ROSH certification.
- The rosin is evenly distributed, with good continuity and no broken core.
- Good solderability, insulation resistance, no splash and corrosion.
- Desoldering, Antioxidant and Corrosion Resistance.
- 60/40 rosin core solder
- Good solderability, strong moisture
- Easy to clean
- High reliability, widely used in electronic products
- Model: CBB61
- Material: Polypropylene Film, Plastic Shell
- Lead End: 2 Wires
- Tolerance: ±5%
- Rated Capacity: 3.5uF
- Rated Voltage: 450V AC
- Rated Frequency: 50/60Hz
- Climatic Category: -40/70/21
- Wire Length: 95mm / 3.7 inch
- Hole Diameter: 4.6mm / 0.2 inch
- Shell Size: 43x31x18mm / 1.7x1.2x0.7inch
- Name: Powerful Liquid Acid Flux Soldering Fluid 25ml solder paste
- Uses: Suitable for battery pole pieces, white steel plate, galvanized sheet, copper iron and other solder series
- Ingredients: ZnO 24%; NH4cl 30%; Hcl 6%; C3H3COH 30%; H2O 12%; surfactant 3%
Use:Increase the wetting effect during welding
- Temperature control range: -50~110°C
- Resolution: -9.9~99.9 when 0.1 °C Other temperature range 1 °C
- Control accuracy, Hysteresis accuracy and Temperature measurement accuracy: 0.1 °C
- Refresh rate: 0.5 S
- Input power: DC 12V
- Measurement input: NTC (10K 0.5%) waterproof sensor
- Output: 1 relay output, capacity = 5A/15A 250VAC, 20A 14VDC
- Environmental requirements: -10~60°C Humidity 20%-85%
- Size: 48.5*40mm
- Power consumption of the whole machine: quiescent current: ≤ 10MA Pull-in current: ≤ 65MA
- Input Voltage: 6V-27V DC
- Maximum Current: 43A
- Input Level: 3.3V-5V DC
- Duty Cycle: 0-100%
- Path Resistance: 16 mΩ @25°C
- Low Quiescent Current: 7µA at 25°C
- Operating Frequency: 25kHz
- Size: 50x50x40mm
- Surface box made of yellow / gray ABS plastic.
- It has an emergency button, with a 40 mm diameter mushroom.
- Emergency button with lock. Inside it has a 1NC type button (normally closed).
- Possibility of making two lateral openings of 22 mm in diameter, for the entry / exit of cables.
- Total size (Height x Width x Length): 75mm x 70mm x 74mm.
(A) Adjustable Switch DC Motor Speed Controller 3V-35V 12V 24V PWM Ultra-small LED Fan Dimmer DC Motor Speed Controller
Module Size: approx. 30*24mm
Working Voltage: DC 3V-35V
Max Output Current: 5A
Control Power: Max 90W
Quiescent Current 0.015A (standby)
PWM Duty Cycle: 1%-100%
PWM Frequency: 10khz
Fine workmanship and good performance.
Stable and reliable.
Easy to use.
Long service life.
Voltage: DC 5V-16V
Continuous Current: 10A
Short maximum current: 20A (less than 10 seconds)
Speed control mode: PWM stepless speed regulation, can also be used to adjust the light
Control mode: speed control potentiometer (clockwise clicked open, continue to rotate clockwise from 1% to 99% speed)
Duty cycle: 0%-99% (0% position is the state of the switch off when the potentiometer is most on the left).
When the current is switched on, the 0.002A (long time no need to switch off the governor is no current).
Efficiency: the maximum efficiency is as high as 98%.
Volume: long 3cm (excluding potentiometer), wide 2cm, high 1.4cm
This DC PWM 2A DC Motor Controller Module allows controlling the direction of a DC the motor using a Pulse-Width-Modulated (PWM) DC voltage with a duty cycle adjustment from 0%-100%. It also has an onboard self-recovery fuse 2A and a Power-On LED light.
Input supply voltage:1.8V-15VDC
Max output power:30W
Max continuous output current :2A
Duty Cycle adjustable: 0%-100%
Size: 5 x 3 x 1.5 cm
DC 6-28 V 12 V 24 V 3A PWM Control Switch Driver DC Motor Governor Engine Speed Regulator
This DC Motor Speed Controller that allows you to control the direction of a DC engine using a DC Width-Modulada (PWM) voltage DC with a fully adjustable working cycle of 0%-100%.
The engine speed controller can easily provide a continuous 3A current for your CONTINUANT CORRENT engine or other DC load.
Input power supply: DC 6 V-28 V
Maximum output power: 80 W
Maximum continuous output current: 3A
Adjustable working cycle: 0%-100%
1) 600 V Cat III safety rating
2) 50% bigger display with bright white backlight
3) Voltage, resistance, continuity, capacitance
4) Input terminal for ac and dc current measurements to 10 A current
5) Diode test, data hold